Mercedes-Benz E W212 - 2013 - 2016 220 CDI 170hp Stage 1 Chip Tuning · ECU Remap
Catalog reference — not a measured result for this vehicle.
Catalog reference: power 170 → 220 bhp, difference +50 bhp (29%); torque 400 → 500 Nm. Actual results depend on vehicle condition and measurement.
Figures are typical ranges; exact results depend on the vehicle's hardware and dyno measurement.
Get a Quote
Mercedes-Benz E W212 - 2013 - 2016 220 CDI 170hp
Book an appointment Find a centreReversible: Yes, the original software is kept
Mercedes-Benz E W212 - 2013 - 2016 220 CDI 170hp — Stage 1 Remap
Stage 1 re-calibrates the ECU software — boost, fuelling and ignition maps — within the factory hardware's safe tolerances. No hardware changes are required.
DPF Delete, EGR Delete, AdBlue / SCR Delete
Mercedes-Benz E W212 - 2013 - 2016 220 CDI 170hp — Software deactivation of the diesel particulate filter (DPF/FAP) functions and fault codes. Verified software is used for AdBlue / SCR Delete, NOx Sensor Delete and EGR Delete fault solutions.
Solutions for this vehicle
Mercedes-Benz E 220 CDI Stage 1: all generations →
Stage 1 Remap
Software that optimises the engine's power and torque maps within safe limits.
EGR Delete
Software deactivation of the exhaust gas recirculation (EGR) valve control and fault codes.
DPF Delete
Software deactivation of the diesel particulate filter (DPF/FAP) functions and fault codes.
AdBlue / SCR Delete
Software deactivation of the AdBlue/SCR dosing system and its fault/warning functions.
DTC / Fault Code Removal
Switching off selected diagnostic trouble codes (DTC) in the ECU software.
Where can this be done near you?
Prime Chiptuning applies the software at its own centres in Türkiye. Abroad, our partners carry out the work with the same files, and workshops can order the file directly.
About the Mercedes-Benz OM651 2.1 CDI (200 / 220 / 250 CDI, 2008–2018)
The OM651 is the 2.1-litre four-cylinder diesel of the post-2008 C, E, GLK, GLC, ML, Vito and Sprinter, offered from 136 to 204 hp. Most versions are twin-turbocharged and the hardware is largely shared across outputs.
How a Stage 1 remap works on the Mercedes-Benz E W212 220 CDI 170hp
Stage 1 recalibrates injection, rail pressure, boost and the torque limiter. The gain is especially clear on the 200 and 220 CDI outputs. A full low-rev torque curve results, matched to the 7G-Tronic or 9G-Tronic gearbox.
Pre-remap checklist
- Injectors and injector seals (Delphi injector issue on early production).
- Timing chain noise and tensioner condition.
- DPF load and, where fitted, the AdBlue system.
- EGR valve and swirl flap mechanism.
This section is based on Prime Chiptuning workshop experience; the power and torque figures come from the catalogue measurement above.
ECUs used in Mercedes-Benz vehicles
If you know your ECU family, its page lists exactly which solutions are available for it.
Mercedes-Benz E — Power Calculator
| Engine | Power | Gain |
|---|---|---|
| 200 CDI 136hp | 136 → 200 bhp | +64 bhp |
| 200 CDI BlueTEC 136hp | 136 → 200 bhp | +64 bhp |
| 200 CGi 184hp | 184 → 230 bhp | +46 bhp |
| 220 CDI BlueTEC 170hp | 170 → 250 bhp | +80 bhp |
| 250 CDI 204hp | 204 → 240 bhp | +36 bhp |
| 250 CDI BlueTec 204hp | 204 → 240 bhp | +36 bhp |
| 250 CGi 211hp | 211 → 230 bhp | +19 bhp |
| 300 CDI BlueTec Hybrid 231hp | 231 → 260 bhp | +29 bhp |
| 300 CGi 252hp | 252 → 312 bhp | +60 bhp |
| 350 CDI 252hp | 252 → 290 bhp | +38 bhp |
| 350 CDI BlueTec 258hp | 258 → 300 bhp | +42 bhp |
| 350 CGi 306hp | 306 → 320 bhp | +14 bhp |