Ford C-Max · 2007+
Ford C-Max DPF Fault Solution
When the DPF (diesel particulate filter) clogs on Ford C-Max (2007+) diesel engines, the car regenerates frequently, power is limited and a warning lamp comes on. Differential pressure and fault memory are checked first, the ECU is identified and a matching software solution is applied after an original backup.
Suitable engines for the Ford C-Max
Year / chassis: 2015+
| Engine | Power | DPF fault solution |
|---|---|---|
| Ford C-Max 1.5 TDCI 105hp | 105 → 125 bhp | ✓ |
| Ford C-Max 1.5 TDCI 120hp | 120 → 150 bhp | ✓ |
| Ford C-Max 1.5 TDCI 95hp | 95 → 150 bhp | ✓ |
| Ford C-Max 2.0 TDCi 150hp | 150 → 195 bhp | ✓ |
| Ford C-Max 2.0 TDCi 170hp | 170 → 200 bhp | ✓ |
Year / chassis: 2011 - 2015
| Engine | Power | DPF fault solution |
|---|---|---|
| Ford C-Max 1.6 TDCI 115hp | 115 → 140 bhp | ✓ |
| Ford C-Max 1.6 TDCI 95hp | 95 → 120 bhp | ✓ |
| Ford C-Max 2.0 TDCI 115hp | 115 → 175 bhp | ✓ |
| Ford C-Max 2.0 TDCI 136hp | 136 → 180 bhp | ✓ |
| Ford C-Max 2.0 TDCI 140hp | 140 → 180 bhp | ✓ |
| Ford C-Max 2.0 TDCI 163hp | 163 → 200 bhp | ✓ |
Year / chassis: 2007 - 2010
| Engine | Power | DPF fault solution |
|---|---|---|
| Ford C-Max 1.6 TDCI 100hp | 100 → 130 bhp | ✓ |
| Ford C-Max 1.6 TDCI 109hp | 109 → 140 bhp | ✓ |
| Ford C-Max 1.6 TDCI 90hp | 90 → 120 bhp | ✓ |
| Ford C-Max 1.8 TDCI 115hp | 115 → 145 bhp | ✓ |
| Ford C-Max 2.0 TDCI 115hp | 115 → 175 bhp | ✓ |
| Ford C-Max 2.0 TDCI 136hp | 136 → 175 bhp | ✓ |
When is it needed?
- DPF full / regeneration warning
- Frequent regeneration and rising fuel use
- Engine warning light and reduced power
- Oil dilution and a costly DPF replacement
Typical duration: 1–2 hours
Frequently asked questions
Can a clogged DPF on the Ford C-Max be solved with software?
The filter and sensors are checked first; any mechanical fault is reported. Where suitable for the Ford C-Max, the DPF software solution is applied to the ECU with the original software backed up and verified by a road test.
Why does DPF regeneration not complete on the Ford C-Max?
Regeneration needs the exhaust temperature to stay high for a while; short trips and city driving do not provide that. Faults in the differential pressure sensor, the EGR or the injectors also stop regeneration. The soot load and sensor values are read first; depending on the cause we recommend a forced regeneration, cleaning or a software solution.
What is a DPF software solution, and when is it needed on the Ford C-Max?
When the filter is too loaded to recover or the fault keeps returning, the ECU software is adjusted so that filter monitoring is switched off. For the Ford C-Max the decision is made after the fault memory and the state of the filter have been checked; not every blockage needs software.
Will the car pass inspection after a DPF delete?
Work on emission hardware can affect inspection and road compliance. This work is offered only for uses permitted by law, such as off-road, motorsport, export or fault diagnosis. Inspection and road compliance remain the owner's responsibility.
Does the filter have to be physically removed?
We handle the software side; physical work on the filter is done in the workshop depending on the car and your choice. If only software is changed and the filter stays in place, it will keep loading up.
Should I try cleaning first?
In most cases yes. If the filter is not yet blocked, a forced regeneration or chemical clean is the better step; we measure the condition and tell you the cheapest route.
Will fuel consumption drop?
On a car that regenerates frequently it usually does, because the extra fuel burned during regeneration cycles disappears.
Other solutions for the Ford C-Max
Ford C-Max AdBlue fault solution
Ford C-Max EGR fault solution
Ford C-Max Pop & Bang tuning
More about DPF Delete
Ford Stage 1 Chip Tuning — How Much BHP?
⚠ Software work on emission systems is offered only for uses permitted by applicable law (motorsport, off-road use, export, fault diagnosis, etc.). Road use and inspection compliance of the vehicle remain the owner's responsibility.