Türkçe TREnglish ENDeutsch DEFrançais FR
Get a Quote
Sunward · Construction Machine · AdBlue Fault Solution

Sunward SWE 60UF AdBlue Fault Solution

We solve AdBlue (SCR) system faults on Sunward SWE 60UF construction machines with ECU software: NOx sensor errors, pump and heater faults, quality warnings and power derate. The cause of the fault is diagnosed first and the original software is backed up.

Get a Quote Find a centre On-site service
ECU software work on a Scania truck and a Doosan excavator in the workshop

On construction machines an AdBlue fault stops the site: once the machine is in limp mode it cannot dig or load, and the crew waits for service. Dust, vibration and long idling shorten the life of NOx sensors and the dosing injector.

The SCR system injects AdBlue (urea solution) into the exhaust to reduce nitrogen oxides. It consists of a tank, pump module, heater, dosing injector, NOx sensors and a control unit. When one of these parts fails the ECU first warns, then starts a countdown and, when it expires, limits power or speed.

The most common faults are the NOx sensor, a dosing injector and lines blocked by crystallisation, and heater and pump modules that fail in the cold. Poor-quality or diluted AdBlue also shows up as a quality fault. We identify which part is actually at fault by diagnosis and recommend the solution accordingly.

When is it needed?

  • AdBlue warning and countdown
  • Pump / injector / NOx sensor failure
  • No-start lockout caused by a system fault
  • High repair cost

Typical duration: 2–3 hours

AdBlue Fault Solution on other Sunward models

Sunward SWE 155FSunward SWE 215FSunward SWE 225FNSunward SWE 335FSunward SWE 90UF

AdBlue Fault Solution for other makes

VolvoAebi SchmidtJCBBobcatManitouZoomlionCaterpillarAtlasXCMGHidromekHitachiKomatsuTerex

Send us this for a quick diagnosis

If you include the following when you message us on WhatsApp, we can confirm compatibility and the work needed the same day.

  • Make, model and model year
  • A photo of the dashboard warning or the fault code
  • A photo of the engine ECU label
  • When the fault started and what has been done so far
  • For on-site service: province, district and location
WhatsApp On-site service

Frequently asked questions

What are the symptoms of a Sunward SWE 60UF AdBlue fault?
An AdBlue or emission warning on the dash, a remaining distance or time countdown, NOx sensor fault codes, power or speed limitation and, on some vehicles, a start inhibit are the most common symptoms.
Can a NOx sensor fault be solved with software?
It depends on the ECU type. The condition of the sensor, the wiring and the SCR catalyst is diagnosed first; if replacing a part is the better and cheaper route we say so plainly. A software solution is applied when our library holds a verified solution for that ECU.
How long does the job take?
Most ECUs are read and written through the diagnostic socket and the job is completed the same day. Some units are removed and worked on the bench.
Can the original software be restored?
Yes. The original ECU software is backed up and archived before the job; the factory setting can be restored on request.
Why does the machine cut power when there is an AdBlue fault?
When the emission system detects a fault, the ECU first gives a warning; if the fault is not fixed it limits torque and engine speed in stages, and at the final stage the machine runs at idle only. This is how the system is designed to behave. Power returns once the cause is fixed or a software solution matching the ECU type is applied.
Will a reset clear the AdBlue warning?
After the tank is refilled, the warning goes out by itself on most machines. If it stays on after topping up, the cause is usually the NOx sensor, pump, heater or level sensor; a reset alone does not last, and the warning and power reduction return. The fault memory is read first and the source identified.
The machine cut power in the middle of a job. Can it be dealt with on site?
Most ECUs are read and written through the diagnostic socket, so the job can be done where the machine stands; some units are removed and worked on the bench. For on-site service across Türkiye, send us the location and machine details on WhatsApp.
What happens to the machine when AdBlue is switched off?
After the software solution the ECU no longer doses AdBlue or runs the related fault monitoring; the warnings, the countdown and the power reduction end, and the machine uses no AdBlue. Engine power and running do not change. Because nitrogen oxide emissions rise, the job is offered for uses permitted by the applicable regulations.
AdBlue emulator or software solution?
An emulator is a separate box added to the machine's wiring that sends the ECU signals as if the system were working; it means extra connections and an extra point of failure. With a software solution nothing is added to the machine: the work is done in the ECU's own software and can be reversed because the original backup is kept. We apply the software solution.

Other solutions for the Construction Machine

Sunward Construction Machine DPF Fault SolutionSunward Construction Machine EGR Fault Solution Sunward SWE 60UF power software and technical dataSunward Construction Machine AdBlue Fault Solution Construction Machine AdBlue Fault SolutionSunward software solutions Truck AdBlue Fault SolutionTractor AdBlue Fault Solution More about AdBlue / SCR Delete Construction Machine →

Let's find the right solution for your vehicle

Send us your vehicle details and your nearest location will get back to you.

Get a Quote Find a centre